Go into graphics settings and change full screen mode to Borderless. ( tooltip cant be shown in full screen mode, seeing what value change in tooltip feedback is necessary for first time configuration )

Read everything in red rectangle boxes

Step 1 —> Open Game and Go into settings.

Go into graphics settings and change full screen mode to Borderless. ( for initial configuration only )

Now go into Key bindings and make the following changes

  1. Right mouse button for ADS ( Aim down sights )
  2. Wheel Down –> Primary weapon 1
  3. Wheel Up –> Primary weapon 2

Step 2 –> Copy all your game keybinds to RCL settings

Copy those key binds which you think affects the recoil of the gun

For warzone

crouching and prone reduces the recoil of the gun, so copy those key binds

You can leave other key binds blank

step 3 –> Configuring RCL recoil macro

CTRL+RIGHT/LEFT is selector ( swap btw which value to be changed )u003cbru003eAny value can be changed with CTRL+UP/DOWN
  1. Run RCL no recoil Engine as administrator and Click on start Button, After that you can minimize the RCL no recoil.
  2. Go into training mode and Equip STG44
  3. Press F1 to activate STG44 no recoil macro
  4. Now Stand near a wall and fire.

    If bullets are going up increase general Recoil multiplier
    If Bullets are Going Down Reduce general Recoil multiplier
  • Ctrl + Right arrow to select general recoil multiplier ( swap through list of things )
  • Ctrl + Up arrow to increase it
changing general recoil multiplier will affect all weapons and all scopes. if you change your game sensitivity in future you can just change this value to quickly tomconfigure RCL macro for your new game sensitivity


That’s it You have adjusted all weapons for no recoil.
Click ctrl+ right/left to see what all other things can be changed

Ctrl +Enter to Save ( After clicking ctrl + enter ; pls wait 1 or 2 seconds before clicking it again )

Test all other weapons and if any other weapon need adjustment change weapon specific multiplier

if any particular weapon need adjustments then change weapon specific sensitivity.

CTRL+ ENTER to save everything (After changing any value you should click CTRL + ENTER to save otherwise next time you start macro the changes wont be there)

Step 4 –> Adding an inventory identifier (for autodetection to work properly)

without this autodetection wont get triggered when you open inventory ( important )
1080p resolution users can skip this step as we have already added it

Open RCL advanced settings

select “Inventory identifier” and then click on Capture

Capture something in inventory screen such that RCL macro can identify if inventory is open or not.

if your resolution is way higher than 1080p then you can capture excatly half of the image to use as inventory identifier

Test this multiple times by moving around and clicking on test button as background is translucent

step 5 –> setting up scan area (for autodetection)

1080p resolution users can skip this step as we have already added it

change open inventory to toggle in game settings (for initial configuration only , after configuration you can revert it back)

press tab to open inventory in game

Open RCL advanced settings

Click on “Set1” and draw a box around gun image

Click on “Set2” and draw a box around gun image ( since only one gun image is showing in the inventory scan area overlaps each other )

Then click on save

(defining separate scan area is good that RCL macro don’t have to scan entire screen for weapon)

Toggle ON ==> Only scan active slot for autodetection (This is needed as scan areas overlap eachother)

Refer this video

step 5.1 –> Adding autodetection using autodetection maker

1080p resolution users can skip this step as we have already added it

Capture something that can be used to identify gun from inside scan areas (inventory screen )that we set in step 4

click on convert

Trim image from all 4 sides such that every time you pick the gun , this image should be same ( since for warzone this may depend on the actual loadout )

then click on save

click TEST Button to check the autodetection ( if you pick the same gun in the game but the image looks different then autodetection wont work. be aware of it )

Tab is the autodetection trigger (So when you equip new gun press tab to open inventory and RCL macro will scan for gun and assign recoil accordingly)

step 6 –> Other things that you can mess around with

  • Weapon specific recoil multiplier
  • each scope multipliers
  • Crouch multiplier
  • Prone multiplier
  • Hip-fire multiplier
  • general horizontal multiplier
  • autodetection trigger delay
2/22/2022 My settings
I play with autodetection enabled , narrator feedback, volume of narrator set to low, game in full screen mode. For me autodetection is working in full-screen mode. ( autodetection in full screen (Experimental feature )may not work for all , it should work in borderless windowed mode ).u003cbru003eTool tip cant be shown in full screen mode, switch to narrator feedback if you play in full screen mode
3/17/2022 My settings
I play with autodetection enabled , tooltip feedback with location on 2nd monitor , fontsize increased , game in full screen mode.For me autodetection is working in full-screen mode. ( autodetection in full screen (Experimental feature )may not work for all , it should work in borderless windowed mode ).

How to play in full screen mode

Open RCL settings and change feedback to narrator feedback. Now you can play in full screen mode.
Tooltip cant be show in full screen mode. So you need to change to narrator feedback.

OR

If you multi monitor setup , set the location of tooltip on second monitor ( see advanced settings >> additional settings )
RCLMacro Engine | Autodetection maker
Logo
Shopping cart